Micro-printers are small, battery-powered, use infrared or Bluetooth technology for data communication, and of course use serial ports; usually portable micro-printers are also called portable ticket printers; mainly used in various mobile applications: such as government mobile police systems , mobile law enforcement systems and other on-site printing law enforcement documents, in addition, such as the insurance industry's on-site vehicle damage system printing fixed loss orders, such as outdoor equipment inspection, logistics system delivery orders and so on. This article describes the instructions for using the micro printer.
Step 1: Connect the printer: Connect the printer and connect the color difference meter as shown below. After connecting, the red light on the printer will be on.
Step 2: Install the printing paper:
1. Open the printer cover: Press the front end of the printer cover slightly --- near the exit of the paper, and slide the printer cover in the direction of the arrow to open the printer cover. Press the front end slightly, slide the printer cover in the direction of the arrow, the power data cable socket, the indicator light, the power socket, and the color difference meter print socket.
2, install the printing paper:
This micro-printer uses thermal paper printing, which has thermal side and no side. Only the thermal side can print the words. The thermal side is installed face down when installing the paper. Install in the direction indicated by the paper arrow (with the thermal side facing down), push the handle to the up position, extend one end of the paper to the bottom of the rolling bar, and pass the rolling bar to place the printing paper and roll The rod can be pushed up and down, and the downwardly-cranked handle is turned to the upward position, and is installed in the direction indicated by the printing paper arrow. After the printing paper is installed in the rolling groove, the green light is on, and the printing paper is as follows. After installation, turn the buckle to the down position.
3. Install the printer cover. If the paper outside the print slot is not long enough, you can operate as follows: first press the “SEL†button, the green light is off, then press the “LF†button, the scroll bar scrolls to drive the paper to scroll up. When it is long enough, press the “SEL†button again, the green light is on, and the scroll bar stops scrolling. Close the printer cover; the paper is completely installed: SEL button LF button to turn the upward button to the down position, the green light is on.
The test method for the printable surface of the paper: use a coin or key to quickly traverse the paper surface, there will be black scratches on the heat-sensitive side, and no heat-sensitive side (the thermal side on the installation side) Install it downwards, please do not install it. If it is reversed, the printed paper will be blank. There is a black scratch on the thermal side. The non-heat-sensitive side has no black scratches.
Step three, print color difference meter detection data
1. When the micro printer is connected, the printing paper is installed and connected with the color difference meter, the green light on the front of the micro printer is in the bright state. If the green light is not bright, press the “SEL†button, the green light is on, at this time the micro The printer can print the color difference meter detection data.
The state is well-installed and printable: Black scratches, the paper is installed properly, the green light is on, and the color difference meter is connected.
2, print color difference meter test data:
After the color difference meter detects the color, it is in the following color data value interface. Press the print button of the color difference meter to print the data. Press the print button several times to print the data value several times.
The printed result is as follows: After the data is printed, the paper with the data can be peeled off from the printer. Press this print button to print.
Step 1: Connect the printer: Connect the printer and connect the color difference meter as shown below. After connecting, the red light on the printer will be on.
Step 2: Install the printing paper:
1. Open the printer cover: Press the front end of the printer cover slightly --- near the exit of the paper, and slide the printer cover in the direction of the arrow to open the printer cover. Press the front end slightly, slide the printer cover in the direction of the arrow, the power data cable socket, the indicator light, the power socket, and the color difference meter print socket.
2, install the printing paper:
This micro-printer uses thermal paper printing, which has thermal side and no side. Only the thermal side can print the words. The thermal side is installed face down when installing the paper. Install in the direction indicated by the paper arrow (with the thermal side facing down), push the handle to the up position, extend one end of the paper to the bottom of the rolling bar, and pass the rolling bar to place the printing paper and roll The rod can be pushed up and down, and the downwardly-cranked handle is turned to the upward position, and is installed in the direction indicated by the printing paper arrow. After the printing paper is installed in the rolling groove, the green light is on, and the printing paper is as follows. After installation, turn the buckle to the down position.
3. Install the printer cover. If the paper outside the print slot is not long enough, you can operate as follows: first press the “SEL†button, the green light is off, then press the “LF†button, the scroll bar scrolls to drive the paper to scroll up. When it is long enough, press the “SEL†button again, the green light is on, and the scroll bar stops scrolling. Close the printer cover; the paper is completely installed: SEL button LF button to turn the upward button to the down position, the green light is on.
The test method for the printable surface of the paper: use a coin or key to quickly traverse the paper surface, there will be black scratches on the heat-sensitive side, and no heat-sensitive side (the thermal side on the installation side) Install it downwards, please do not install it. If it is reversed, the printed paper will be blank. There is a black scratch on the thermal side. The non-heat-sensitive side has no black scratches.
Step three, print color difference meter detection data
1. When the micro printer is connected, the printing paper is installed and connected with the color difference meter, the green light on the front of the micro printer is in the bright state. If the green light is not bright, press the “SEL†button, the green light is on, at this time the micro The printer can print the color difference meter detection data.
The state is well-installed and printable: Black scratches, the paper is installed properly, the green light is on, and the color difference meter is connected.
2, print color difference meter test data:
After the color difference meter detects the color, it is in the following color data value interface. Press the print button of the color difference meter to print the data. Press the print button several times to print the data value several times.
The printed result is as follows: After the data is printed, the paper with the data can be peeled off from the printer. Press this print button to print.
Office Furniture Series,Meeting Table Parts,High Cabinet,Low Cabinet
SHENZHEN CHANGJIANG FURNITURE CO., LTD , https://www.findcjf.com